New clarification added: Dear Bidder Please find the below clarificiatons as follows: Q1 - بشأن تكلفة الخطة البيئية ESMP والذي تكلفتها 16900$ هل نضيفها فوق الكميات او ماذا يقصد بها Ans 1 - Regarding the ESMP, please refer to the e-sourcing document tab for each LOT; there will be a document titled "ESMP," which pertains to the Social Environmental Management Plan. This document must be signed and stamped to confirm your agreement, For the estimated amount of $16,900, as determined by the World Bank and UNOPS for implementing the plan. The supplier will need to review and take into account the costs associated with the implementation of the ESMP processes in case awarded. Regards 

Edited on: 24-Mar-2025 00:12

Edited by: webservice@unops.org

New clarification added: Dear Bidder Please find the below clarificiatons as follows: Q1 - We kindly request you to reduce the production capacity of the submersible pump slightly, by no more than 15%., since the required pump is not available in the market from all suppliers, This matter is up to you to make the decision, as we have presented our proposal.? Ans 1 -Please share the tenders and item specsRegards  

Edited on: 23-Mar-2025 23:53

Edited by: webservice@unops.org

New amendment added #3: The purpose of this amendment is:Extended the tender deadlne. Extend the tender clarifications​Therefore please note the following changes in esourcing tabs:The Esourcing General tab amendedThe tender deadline was ''24 March 2025'' and will now read as '' 07 April 2025'' Extend the tender clarifications was '' 12 March 2025'' and will now read to read as '' 26 March 2025'' All other terms and conditions remain the same.

Edited on: 23-Mar-2025 12:16

Edited by: webservice@unops.org

New amendment added #2: The purpose of this amendment is:Update the LOT 2 - Phase 01 - BoQ as amendment 001 - Update LOT 2 - Phase 01 - BoQ - Distribution Network tab to read as  '' Item 1.1.1 section A to read as '' DN 180  mm Dia''. Update LOT 2 - Phase 01 - BoQ - Distribution Network tab to read as  '' Item 1.1.2 section A to read as '' DN 125  mm Dia'' Update the LOT 2 - Phase 02 - BoQ as amendment 001 -Amendment 001 - LOT 2 - Phase 02 - BoQ - Distribution Network tab to read as '' Item No. 1.1.1 - A  DN 180 mm Dia.'' Amendment 001 - LOT 2 - Phase 02 - BoQ - Distribution Network tab to read as '' Item No. 1.1.1 - A  DN 300 mm Dia.'' Amendment 001 - LOT 2 - Phase 02 - BoQ - Distribution Network tab to read as '' Item No. 1.1.1 - A  DN 125 mm Dia.'' Update  LOT 2 -  3 - 5B-Phase Two PROFILES DRAWINGS​Therefore please note the following changes :The Esourcing Document tabAdd Amendment 001 - LOT 2 - 3-5B-Phase Two PROFILES DRAWINGSAmendment 001 - LOT 2 - Phase 01 - BoQAmendment 001 - LOT 2 - Phase 02 - BoQAll other terms and conditions remain the same.

Edited on: 17-Mar-2025 06:08

Edited by: webservice@unops.org

New clarification added: Dear Bidder Please find the below clarificiatons as follows: The quantity tables for the HDPE water network do not include the diameter of 125 mm while this diameter is present in the drawings (Plane). - The profiles indicate that the pipes are Ductile Iron with a diameter of 150 mm while in the drawings (Plane) as well as the quantity tables they are made of HDPE material with different diameters.There is a diameter of 400 mm in the quantity table but it is not present in the drawingsThe diameter of 160 mm is mentioned in the quantity tables and this diameter is not present in the drawings.The diameter of 180 mm is mentioned in the drawings and this diameter is not present in the quantity tables.For all the above clarifficiatons , Please refer to Amendment 001 - LOT 2 - 3-5B-Phase Two PROFILES DRAWINGS, Amendment 001 - LOT 2 - Phase 01 - BoQ. and Amendment 001 - LOT 2 - Phase 02 - BoQ.The specifications for the tapping ferule and saddle are to be made of gunmetal and its accessories of nails are stainless steel. These specifications apply if the pipes are ductile iron. Note that the tapping ferule and saddle are very expensive and do not necessarily have to be used with HDPE pipes. The specifications also indicate the type of ferule strap that has a push-fit system. This system is not available in the local market or in the markets of neighboring countries, and importing it from Europe requires a long time.Please refer to item 1.2.6: Supply and install Single Ferrule on DI mains. A small quantity will be utilized to connect with the existing networks. Kindly ensure full compliance with the RFQ specifications and requirements. We hope to agree to extend the deadline for submitting the tender so that we can obtain appropriate prices for the materials, since more than 60% of the project value represents the value of the materialsExtension had already been granted in prevoius amendment. We hope to clarify the pipe pressure, as only limited items were mentioned, which is 16 bar pressure, and the rest of the items did not mention any details about the required pipe pressure. We hope you can clarify for each country.The minimum  system pressure requirement  is PN16 The pipe diameters in the drawings are 300 mm, 180 mm, and 125 mm, but these diameters are not listed in the Bill of Quantities, which specifies the following diameters for the pumping line: 400 mm, 250 mm, and 200 mm, while the diameters for the distribution network are 160 mm and 90 mm."Please refer to Amendment 001 - LOT 2 - 3-5B-Phase Two PROFILES DRAWINGS, Amendment 001 - LOT 2 - Phase 01 - BoQ. and Amendment 001 - LOT 2 - Phase 02 - BoQ.Regards 

Edited on: 17-Mar-2025 02:02

Edited by: webservice@unops.org

New amendment added #1: The purpose of this amendment is:Extended the tender deadlne. Upload pre bid meeting minutes.Therefore please note the following changes :The Esourcing General tab amended:Deadline to read as 24 March 2025 The Esourcing Document tab Add Pre-Bid Meeting -  Prebid Meeting RFQ-2025-56464All other terms and conditions remain the same.

Edited on: 11-Mar-2025 15:47

Edited by: webservice@unops.org